Feb 15, 2009

Having stuff available

In our hobby it is very convenient if you continuously have all possible required parts available for 'the next project'. This story concerns bragging about pulling the rabbit out of our sleeve on demand. But to be more seriously; this is where we have grown over the years by carefully choosing the right parts, and buy large quantities each time, at flea markets and keeping so called 'obsolete old stuff' conservatively stored instead of throwing it away. Also, if you can build something and it works well, build more of them as they will become handy in time.
But it is not at my place, it is at my friends QTH. His garden is growing all kind of vertical constructions all the time, year in year out.

K9AY and Magnetic Loop
To put PA3FGA's K3 and the all new Perseus to the test, various RX antennas are put up and compared against the short 160m reference vertical in the front garden. There's also a wideband NVIS dipole at 1m70 height available. Mind you, we do test antennas 90% for 160m use.



The K9AY antenna box is my MKIII version. It was build just before a test-weekend on Friday night in total darkness. We started with a brand new version MKIV, which earlier during CQWW CW in 2008 at our PI4TUE club station, showed open circuit 100nF caps. While trying to do the F/B adjustment on the termination resistance, other problems turned up. That's where the available old MKIII antenna box was put in action again. It's nice if you have spares available :)
The second antenna is a simple magnetic loop made from a 5mtr length 22mm dia copper tube. On the top a water bottle (rain protection) contains a strap of doorknob capacitors. On the bottom an FT240-K ferrite with 8 windings inside another bottle holds the 50 Ohm output coupling, followed by a coaxial common mode filter.




The magnetic loop is mounted to a thickwall glass-fiber pole, which in turn rests on a spare antenna rotor. At first it was mounted at 1m from the ground only. This gave it a low Q and thus a relatively wide BW. At this new height the BW has narrowed to a more relevant 20 Khz.

How do they perform?
The K9AY, after careful alignment of the termination resistor, shows 2 to 5 S-units F/B on 160m. Times the 3-4 dB (which is average for S-meters) we get a result which is common for this antenna. This version of the K9AY is our 10th time we have set it up and the 3rd time in this backyard. It is a useful RX antenna in which you can quickly switch in the 'backside null' in 4 directions.
The magnetic loop has narrow nulls off the sides and after some 5 weeks of use it does not show any real advantage over the other available RX antennas (short vertical, K9AY and NVIS).

Let's do 7 MHz antennas this weekend
Not only because we want to listen on 40m but Rens, PA3FGA also likes SWL AM broadcasting on 41m shortwave. He wants a full size dipole, hung from the available glass-fiber pole and a resonant vertical for comparison( actually that last one was my idea). So the K9AY and the magnetic loop have to go.
The K9AY central pole is lowered, the guying wires winded on the cable reels. The anchors pulled out of the lawn and cleaned. The MKIII antenna box removed and all stored in a box for the next possible field operation.
Two lengths of wire are cut for dipole resonance. Now for connecting the central coax a current balun is needed. Let's see what we have in the box?



The ferrite and copper wire were bought from Amidon (or their supplier CWS ByteMark for that matter) some years ago. On the right you see ready-to-use build versions in a box; the white one is an FT240 type 67 toroid and the green one is a type K. The #67 is better suited for 20-10mtrs, the K version is better for the low bands. We used these in our multiband verticals during summer holidays in Liechtenstein/HB0.
The other pre-wound baluns have F150A-K toroids and multi inputs suitable for 12.5/18/25/28/32 Ohms depending on which winding taps were chosen. See the book of W2FMI for details on this. All baluns are XXXL style built and way overrated.


The above balun was our first one build. We used this on a low full size 160m dipole and tested this during the CQWW-CW contest in 2003 on a farmers land and a portable set-up. We made 200 qso's from 21:00 till 00:00 during Saturday night, just for fun! The balun is not black-burned; it is a coating spray against moist. And the little box normally holds...euh held some of the lesser used spices in the kitchen closet.
The 3Y0X hat is only for cold weather protection.
Rens sent in the log and got rewarded by this diploma. I recall that I was the op at that time... oh well today's story was about bragging, right?



The full-size 40m dipole is quickly hoisted up to about 10mtrs AGL and attached as an Inverted Vee to anchor points left and right. Coax was already available from the magnetic loop experiment. A quick check on the network analyzer shows a wide dip at 6.9Mhz. Good enough. The 40mtr band ends at 7040KHz for TX anyway :)
Next we collected the 7mhz vertical+ top loading capacity hat (see my earlier blog from sept 14th 2008) from his garage and put it on the mounting post in the middle of his backyard. This is a fixed mounting location with a 3mtr 22mm dia copper ground pole, some 8 buried radials and a buried Ecoflex-10 coax going to his shack. It has served many, many (test-)antennas already. A 5-minute job only and we are also in business vertically polarised with a perfect SWR.



The right leg of the INV-V is attached to a convenient tower section, which was extended by wooden stick( a spare garden tool). You see, it's always wise to keep also tower parts available!
We had to cut some branches
high up in the tree. These would otherwise tangle up with the other leg.

How do they perform?

On saturday evening the PACC contest is on and we monitor our clubstation PI4TUE efforts on 40m. On large distance contacts their high dipole (@70mtrs AGL) hears Asia and USA better, but on the short to medium distances our lowish Inv-V is clearly the winner. Just as what might be expected. The vertical offers more man-made noise and still has to show its dx capabilities in terms of signal/noise yet. But it is an early first night. We will have to test these antennas for some weeks.

What antenna do we want to build next?
As we are restricted by domestic garden boundaries, the list stops at:
- NVIS dipole wideband (2x8mtr legs@1m70 +32:1 balun) up in the side yard
- Inv-V for 40m up in the back yard
- Short vertical with capacity hat for 40m up in the back yard
- Short resonant RX vertical 160m up in his front yard
- Full size Multiband 10-12-15-17-20m 0.25 grounded vertical up in the side yard
- Short resonant phased RX verticals 160m
- K9AY (several)
- Full size multiband 30/40m 0.25 vertical
- Extended 40m vertical (11m85) with short elevated radials (1/8@4mtr height)
- Full size Multiband 10-12-15-17-20m extended vertical with resonant elevated radials
- Magnetic loop (2 different heights tested)
- Inv-L 160m with 12m vertical part + 2 elevated radials (fire in da hole!)
- Short 160m (23m)vertical with center coil
- Various multiband antennas preparation for field use (HB0-2007&2008)
- Commercial trapped 10-40m vertical (abandoned, bad performance)




The above corner shows some 'spare tools for ground mounted verticals'. The other pic shows some plastic posts, convenient for your vegetable-garden. And for beverages. There are some 150 more in his barn.
Rens is not married. His YL allowed all this in their garden and even recently build a K1, and a K2.
Life is a matter of priorities

I'm going to bed now :)


Jan 28, 2009

Receving splitter

W8JI 'Magic T Combiner/Splitter

For feeding the RX inputs of both my Elecraft K2 and TenTec Orion with the same RX antenna, I'm in need for an antenna splitter.
Tom has great information on this subject on his website at http://www.w8ji.com/combiner_and_splitters.htm

I have choosen the design with the 2:1 step-down transformer and the T-combiner using the proposed type 73 binocular ferrites and some thin teflon coated silverwire I have in my junkbox.



Don't forget the 100 Ohm resistor as I did initially, or you end up with a miserable port-to-port isolation!
Measurements show a port 1 to port 2 isolation (and vice versa) of 26dB at 1820KHz.
I'll be using this splitter for the lowbands, mainly 160m so this will be sufficient.

Antenna connectors in your system; TRX vs RX only
Since my home setup is becoming larger, now that I have more antennas put up, I figured it would be a good idea to make a decision on using a different standard connector for all RX antenna wiring in my shack. You don't want to end up accidently transmitting into an RX antenna, or RX input of any rig.
There are currently 3 popular RX connector types:

F-connector; commonly used in the USA in combination with the cheap available RG6 coax
Cinch-connector; used as RX antenna input on most transceivers
BNC- connector; professional and reliable, used on transverters and Elecraft transceivers

Discussing with Rens/PA3FGA, with whom I do a lot of ham experiments, we decided to use BNC from now on only. I had some available as you can see, but there's certainly two items on the list for the next HAM flea-market :)


RX patch-box with common mode filter
Now is a good time to remove the bunch of heavy coax and stuff from the back of my Orion and create a separate 'patch panel' setup with a coax common mode filter. The coax is 2.5mm RG316 Teflon type. The ferrite core is an FT150A-J (#75).


If you look carefully you will see I missed something in the whole process. Anyone noticed this ?


The new RX patch panel board
No big deal yet, but it's a start.



Does it work?
Sure it works fb!
The Orion is true king in reception on 160m. However, the K2 is in its own league, especially when using the analogue audio peaking filter.
In just 30 minutes I heard 5x JA
and 1x USA on my short 20ft reference vertical. At 22:30 UTC that is. Conditions on 160m are simply marvellous these these days

Future wishes?
Yes, I want another one for field day use. And another for splitting the RX output of my 144Mhz transverter. That is on 28Mhz where the above splitter shows only 15dB port isolation. So I will need to carefully design a different splitter using a more suitable ferrite, like #43 or so.


Dec 31, 2008

New 430 MHz antennas part II

Finally a relay was found
The previous mentioned coax relay type CX520D was found, but it is way too large to fit inside the weatherproof box and have 3 N-connectors connected.
Some more digging inside the junk closet offered a smaller version CX120A. This one has direct solder contacts with 5mm coax entries. After several unsuccesfull direct plumbing attempts, I decided using 5mm teflon RG142 coax as pig tails. Perhaps costing some tenths of dB due to possible minor SWR mismatches, but then again loosing the N-connectors is already 2x 0.15dB (theoratically).
Ah forget about the dB-Bullshit; it will offer fine QSO's I'm sure!

Not the slickest looking solution, but done with care for reliability.
The IP66 plastic box outlets are weatherproof, but I added liquid rubber for additional protection.





The coldest night in Holland for 2008
Early this morning I found that the 430Mhz omni vertical was affected by last nights -9 degrees celsius frost. Our coldest night of 2008 !


That is not white paint but frost; see the close-up.

The coaxes are cut and have N-connectors.
Another antenna preparation ready for the soon-to-be antenna overhaul.

Dec 27, 2008

New 430MHz antennas

There's currently a lot of VHF/UHF antennnas lying around here. Some from fieldday setups, holiday/contest packet links, or just waiting for 'that new project'.
Well since there is very little activity in CW/SSB on 430MHz, I never got to setup a decent yagi at this new QTH. I'm not into UHF dx'ing anyway; my focus lies on 50/144. You can't do all bands, unless you spend (too) many time in the shack, right?
FM repeater dx'ing is something I do like and since I'm preparing new omni-verticals, I decided to add one of the available yagis to the new mounting bracket.

This is a Flexa type FX7044, 16el for 430-440Mhz. Boomlength is 3.10mtr. The Flexa Yagi, is extremely light weight (1.7Kg) and has the lowest windload on the market. Its 2mm dia steel elements are subject to discussion in terms of achievable gain, but for my application it is perfect.


The white spots indicate spray paint. It is a special spray paint which can be used on all surfaces and even rost. I'm using this for endured weather protectection, other plastic sparys etc. never did last very long.

What's next?
Both antennas connect to the same UHF rig, so a coax switch box is needed.
There must be a CX520D coaxial switch somewhere in that closet.....


Dec 4, 2008

CQWW CW 2008

Preparations at PI4TUE
To tell you the truth: not many of us were prepared for this contest. Domestic issues, heavy workload @QRL and stuff, prevented us from a decent preparation. However, Aurelio/PC5A did a great job in getting the clubstation PI4TUE ready on time. He had to climb the roof tower on friday afternoon before the contest, to fix the SteppIR, which again had a major tilt and azimuth offset. It just will not clamp.

We set up our only RX antenna, a home made portable K9AY, just 4 hours before the start of the contest in darkness. Initially it showed no directivity whatsoever. We could not find any error but noted that disconnecting the ground had no effect. The ground connection consists of a 1m copper pipe and 4 additional radials. Usually the ground stake is sufficient enough. Adding the radials makes this antenna even work fb at a rocky 2030mtr ASL mountain top. Upon examening the switchbox, a decoupling cap to ground proved open circuit.


Switchbox+common mode filter(blurry pic). Mark-IV version of K9AY switchbox undergoing repair. The shack of PI4TUE, being the student clubstation of the Eindhoven Technical University (ESRAC), certainly had lots of spare parts available. At T-30 or so, the K9AY showed a F/B performance of several s-units on some european stations. That's good , right?

Available antennas

  • 40m+80m dipole at 65mtr AGL
  • SteppIR yagi at 75mtr AGL
  • HF2V vertical for 40m/80m at 60mtr AGL
  • 2x 0.25 wave 160m sloper at 65mtr AGL, direction USA and JA
  • K9AY at ground level
Contesting


Mark/PA5MW and Rens/PA3FGA during the night shift. Yes that's a 'capo', and a real one!

The new SteppIR performed very well; especially the bi-directional option was appreciated much.
Rens' Elecraft K3 #371(?) performed as expected; great RX on both main and sub-receiver. However, it showed some minor quircks: VFO A/B dropping out of sync, occasional strange offsets and during the first night a total backup reset via RS232 was neccessary to get it going again. Oh well... the firmware is still maturing and I have seen great devellopements during the last 12 months.
Operation-wise it's not my cup of tea. The Orion is a better (contest) rig; it offers far better manual control and view of all current settings. Next the Orion's antenna and VFO distribution and controls are clear and versatile. For me it sucks on the K3. We have been discussing several days on how to setup the K3 for true diversity and being able to switch back to "normal L+R" reception of RX or TX antenna's, without having to use more than a single button and certainly not having to enter (audio)menu's. On thursday I found a schematic on how to switch in/out from true diversity RX on both L+R ears, using an outboard antenna splitter on the K3 main and aux antenna inputs. This was cleverly designed by Bill W4ZV, who used to have an.......Orion :).



Ground connection on back of Elecraft K3 + common mode filters.
Next; one operator in desperate need for another espresso!

The David Clark headphones sure help in the noisy environment; since the PI4TUE shack also accomodates many local 2m/70cm/23cm/13cm FM repeaters, packet nodes, packet &psk31 links and zillions of network computers.

160m RX antenna performance at PI4TUE, or ..... the lack of
We have to do some more experiments since none of the tried 160m rx antennas has offered better signal/noise than our TX quarter-wave slopers so far, including this one. Despite the shown local F/B it did not offer any dx at all.
Over the years we have tried:

- KAZ on the north rooftop @60mtr ASL
- Magnetic loop on rooftop @60mtr ASL
- K9AY on the north rooftop @60mtr ASL
- K9AY at ground level, 110m north of the large shack building, 30m from a low building
- 160m short vertical at ground level, 80m north of the building
- K9AY at ground level, 180m west of the large shack building, 20m from a low building

K9AY & 160m short vertical used copper ground stake 1m + buried copper radials

The PI4TUE shack building is about 60-70m high, has a full metal frame on the outside. It accomodates a full size TX/RX 0.25 sloper on the west (dir. USA) and NE(dir. JA) side.
The above mentioned K9AY and 160m short vertical have been used at several other locations in which they performed very well with the exact same coax lengths and hardware. Difference is that at PI4TUE the coax travels from ground level along the building, some 50mtrs upwards to the shack room, 40mtrs away from the west-TX sloper. This long vertical travel will certainly not help making any antenna quiet.
This contest weekend , again we suffered from a RF noise level on the K9AY that no dx was heard at all. Is it local man made noise from the university buildings? The city environment? We will do a comparison measurement soon on a very short vertical, both at the university area as well as in one of our domestic field locations using a spectrum analyzer.
Both the TX slopers offer some reasonable F/B, thanks to the metal framework of the building. As such it was the best rx-antenna currently available.

Food, beverages, couch for crushing...



The next-door 'living room' with eat & sleep accomodations.
And Rens making true espresso or capuchino using Diemme ..something? I will do a seperate blog on his barrista qualities soon !

Operators
In no particular order: Aurelio/PC5A, Sjoerd/PA0SHY, Harry/PE2HD, Frank/ON9CC, Rens/PA3FGA, Mark/PA5MW.
And those who helped on friday afternoon/evening: Claudia, Steef/PA0IB, PA4A



From L to R: Aurelio, Sjoerd, Harry, Sam.

Was it fun?
Yes, it was fun as ever, being with hamradio friends together and contesting. 40 mtrs was just a-m-a-z-i-n-g. We need to pick up this momentum and go for the next contests in Q1 2009: CQWW160mCW, PACC, ARRL DX CW and ARRL DX SSB.

Summary:
Band QSOs Zones Countries
------------------------------
160: 299 14 56
80: 496 20 80
40: 655 33 117
20: 919 34 115
15: 241 24 66
10: 0 0 0
------------------------------
Total: 2610 125 434 Total Score = 2,855,931

Despite only having a single "3-bander"yagi , some dipoles, slopers and verticals, being at +60m AGL does help. It is a privilege to use the schack and living room. Thanks to Sjoerd/PA0SHY, Steef/PA0IB and Martin/PA3DSC for their efforts they put in building/maintaining the PI4TUE/PI5HEV university clubstation.


untill the next one...

Nov 16, 2008

Give me a reason NOT to buy;

dynamite, a gun, barbed wire etc....
Possession is all strictly prohibited in our country.
All for many good reasons. But after our latest 'experience', reason is a bit lost here.
Oh well.... get over it !



Above picture shows the result of our burglar visit.

What happened?
02:30 AM; I wake up because of a crackling loud sound. I switch on a bedroom light and go downstairs to the living room. There I find nothing abnormal; all doors are correctly locked, all windows seem OK. So back to bed again. I sleep quickly, so QSY zzzzz...
02:45 AM; again this loud noise. Instead of going downstairs, I put aside the window curtain, look downside left at my parking lot.....to see a guy in total black tight clothing, hand gloves and baseball cap. Upon detection he winks his fellow man and both run away quickly. There's an attempted burglary going on.
I jump into my hobby overalls, put on a pair of sneekers, open my front door and run into the direction they went off. I spent some 7 minutes looking at several cars, checking alleys and several roads.
It is not my intention to force a confrontation being alone without any arms whatsoever, but at least I want them to know that I do not just sit back and p*** my pants. And besides, I was being just a bit upset...

Burglar result
Using a 200m glass sucker, they tried to break the lock of the sash windows, which are on the side of my house where the parking lot is. They needed several attempts before the plastic window-chassis broke.
Only one lock of the outer windows is broken before they were detected while performing their profession.
No other damages have been found.

Police assistance
I call the alarm number at 02:55 AM and report the attempted burglary. At 03:30 they arrive, look at the window and enter my house to write a report. Upon their leave I ask if there have been any other attempts recently in my area; "no, not that we would know".
Later that day,I'm visited by two officers of the forensic research who take prints of the glass sucker and a hand glove on the second inner window.

Property owner action
Since I never open these windows, I decide to fixate the window permanently using glue. Next, I have cut some 25x25mm bars to block the windows:




More protection is needed; a Halogen floodlight with motion detector is mounted on the bottom of my antenna tower. It switches in after dark automatically.

The back fence can use an upgrade too; so I add a new layer of treated plywood. The most vulnerable part is done first. Next week I will do the rest.



Next to installing extra safety-locks, there are some more tricks&tips I will
be implementing this week.

Neighbourhood monitoring
A quick check at the closest neigbours revealed that there was a succesfully burglary 6 doors away, just the other week. Talking to these people and others across the street I learned that 2 more houses in our area have been victims last month. Would have been nice if there had been a short informing letter to everyone. Let's start doing that ourselves.

With regard to possible psychological effects

I experience no anger, extreme frustration or other negative effects. In fact I went to bed again 30minutes after the police left the house that morning. But I do understand very well that such might show up sometime. For now let's just say that at this point I regard the whole story a 'negative business encounter'; they want something from me, I want to avoid that deal as much as possible. I need to put more effort in my work there.
The story is different for my girlfriend though. Thank god she slept through the whole story. But she's seeing burglars everywhere and she hasn't slept well ever since. I'm doing my best to bring back that comfort to her.
Let's end this with the simple fact that there are other more serious issues in life and we will grow over this too.


If you have any tips or remarks, please feel free to add any comment




Nov 2, 2008

New omnidirectional verticals for 145 and 430 Mhz

The Half Wave Sleeve Antenna
This model acts similar to the typical J-pole designs; a 0.5 wave radiator plus a 0.25 matching section. However, the coaxial pipe or sleeve section in this antenna has a much better choking action. This should keep the coax free from radiating and result in a better radiation pattern. In theory that is.
The popular J-pole is easier to construct, but the brutal feeding of the (unbalanced)coax to the (balanced)matching section is questionable. But there are new, better variations of the J-pole.
And let's not forget; both offer plenty of fun as they are very efficient antenna's.

Bad alternative; the commercial 'collinear' dual-band vertical
OK, I admit; I have used these typical white fiberglass collinear constructions for years. Everyone has (had) one right? It is by far the most succesful commercial antenna for VHF/UHF. Offers plenty of QSO's too, nothing to bash about that. I still have a 'short' Comet GP3 VHF/UHF for portable use.
But as soon as SWR acts funny you start investigating what this antenna is all about.
What I do not like:
- collinear sections, having no true stacking distance, do not offer the "theoretically calculated" gain. Funkamateur magazine did a comparison between a single rod 5/8 home made antenna and various commercial collinear antenna's back in 2005. Even the super 3x 5/8 (5mtr high) offered no more than some 2 dB gain.....
- bad connection joints "offer" a variation in SWR in due time
- capacitor failure in the bottom section
- 3 metal spokes function as 'groundplane'
When opening up such antenna you find pieces of welding copper, matching coils and small ceramic caps.

The Sperrtopf (german) or Fietspomp (dutch) antenna
Actually this sleeve antenna was designed by A.B. Baily and described in u.s. patent #2184729 in 1937.
The german word 'Sperrtopf' refers to its coax sleeve section.
The dutch word 'Fietspomp' refers to what it looks like; a cycle-pump. I always found them very ugly to look at, but this is not about cosmetics but performance & durability.
You can find some more info on how to build your own at: http://www.timroberts-vk4yeh.id.au/downloads/sleeveantenna.pdf


The 438-470Mhz Sirtel CX400D
I bought 2 of these a few years ago on a flea market. There's already one on my roof, see my blog of feb 24th.



To get them to resonate correctly in our 70cm UHF band section, I need to lengthen the radiator by about 6cm, or was it 8cm? Darn! Why do I forget to write down such evident info? My antenna analyzer stops at 30MHz. Well, l know someone who has an HP network analyzer AND makes great coffee. I will do a separate blog on his Barrista qualities soon :)



See above a really pathetic attempt to measure and adjust the radiator length. Surely the HT batterypack was near empty. And so was the reserve pack.
Let's finish this blog quickly and go to that coffee....

The Wimo 145MHz version
www.wimo.de offers a finished version at an extremely cheap price.
I pop-riveted the short alum mounting section to a clamp. A few layers of spray paint should ensure weather durability. The horizontal tube section is meant for creating a distance from my antenna tower, in order to get the best omni pattern. Mind you; I cannot mount this antenna on the top of the tower. Local restrictions do not allow this. Long story, let's not go there.
It is all about maximizing efficiency and setting priorities.




Where was I ?
Ah, time to get me that coffee :)



Oct 26, 2008

SteppIR @ PI4TUE - Part III

The final day of this project.
Me and my XYL went to her family
during the whole weekend, so again I was not able to join in. I had a great time in former Y22-country; enjoyed the superb hospitality, played with the kids of her sister etc.... Life is good, even without antennas.

Preparation for the last steps
More helpfull hands, safety tools, helmets, first-aid kit, everything to make this day a succes.
Again, you absolutely need perfect weather to work on a building roof at 220ft level. This turned out to be a beautifull day.

- Steef/PA0IB, Rens/PA3FGA, Aurelio/PC5A (wrapped in climbing gear)
- Assembling the prepared boom parts



- Tram trolley and protection against the existing guying wires by covering them with lengths of used plastic hoses.
- Steef/PA0IB assembling the control wires




- 6mtr add-on optional element
- Truss wire, not a luxury at such a height.



- 'Partly beam' just hoisted up in the air
- First-aid chick on standby
- Mind you; this is a small platform he is sitting on




- Lunchtime in the living room/kitchen/ contest sleeping room of the club station ESRAC at the 13th floor of the Technical University of Eindhoven
- L to R: Rens, Aurelio, Claudia, Steef





- adding elements
- "Look ma, no hands"




And then there's Murphy
OK, so what's different in the above second picture ?
The ground crew noticed a loose screw on the boom clamp of one of the reflector 'EHM' units. These had been loosened before to install the boom truss wire. Holy crap...!
So the whole ^%@## yagi had to be lowered again....
It is at this point that physical stress turned into overload as happened to Aurelio; suddenly his forearm muscles simply blocked and next his fingers were cramped-locked together. He got down and Rens took over.

- Switch of tower-operator
- Steef finalizing the control cable on the new Emotator FX1200 rotor





- On the left: HF-2V 40/80m vertical (not visual)
- SteppIR 3 el Yagi
- VHF antenna mast, including full size 40 and 80mtr dipoles
- Crossing the street-light; 160mtr sloper wire, barely visual



This final job lasted the whole day. Totally exhausted they left the premises at 18:00
During the week the antenna tested successfully ! This new antenna will certainly bring some new momentum in the coming contests.
In the meantime I have seen the antenna from ground level, it looks intimidating.

Again a job done very well guys !